Free interactive pavement tool
Sealcoating Calculator
Sealer needed = area × coats ÷ label coverage. A 400 ft² two-car driveway takes about 8 gallons for two coats at 100 ft² per gallon. A contractor charges about $0.15 to $0.30 per ft², and most driveways land at the $150 to $400 minimum.
- Free, no signup
- Results on submit
- Planning estimate, not a quote
Short answer
How do you calculate sealcoat?
Divide the area by the label’s coverage per gallon, then multiply by the number of coats: gallons = square feet ÷ coverage × coats.
A 400 ft² driveway at 100 ft² per gallon needs 8 gallons for two coats, which means buying two 5-gallon pails. A contractor charges about $0.15 to $0.30 per ft², and most home driveways land at the $150–$400 minimum charge.
Coverage depends on the product and how rough the pavement is. Use the rate printed on the label you are buying.
Jump to section
Calculator
Calculate Driveway Sealer and Sealcoating Cost
Complete the inputs, then calculate. If an assumption changes, submit again to refresh the documented result.
You can outline the area on a satellite map when you request quotes, and the form works out an estimated square footage. See how it works.
Before you use the result
What this estimate covers
This sealcoating calculator answers the three questions people ask before sealing a driveway or parking lot: how much sealer to buy, what it will cost, and whether now is the right time.
Sealer & cost turns length × width (or a known area in square feet, square yards, square meters or acres) and the coverage on your sealer's label into gallons and whole pails. It then shows the do-it-yourself material cost beside a professional range of $0.15–$0.25 per ft² for one coat or $0.20–$0.30 for two, with the $150–$400 minimum most crews charge. Those are the national planning figures from our sealcoating cost guide; enter a local bid to replace them. Add the feet of cracks to fill and the crack-filling cost is shown separately, the way contractors quote it.
Area covered reverses the math when you already have pails in the garage. When to seal checks the pavement's age, last coat, cracks, traffic and the weather, and tells you whether to seal now, wait for new asphalt to cure, crack seal first or repair first.
There is no universal coverage rate. Retail driveway sealers and commercial concentrates list different coverage for smooth and rough pavement, so use the label or data sheet for the product you are buying. The example rate of 100 ft² per gallon per coat is only a starting point.
DIY vs. hiring a pro
How Much Does Sealcoating Cost?
Professional sealcoating runs about $0.15–$0.25 per ft² for one coat and $0.20–$0.30 for two. Small jobs carry a minimum of about $150–$400, so most driveways cost the minimum no matter their size. Crack filling is quoted separately, about $0.50 to $3.00 per linear foot.
| Surface | Sealer (2 coats) | Pro cost (2 coats) |
|---|---|---|
| 1-car driveway (10 × 20 ft) | 4 gal · 1 pails | $150–$400 |
| 2-car driveway (20 × 20 ft) | 8 gal · 2 pails | $150–$400 |
| Long driveway (12 × 80 ft) | 19 gal · 4 pails | $192–$400 |
| Small lot (5,000 ft²) | 100 gal · 20 pails | $1,000–$1,500 |
| Medium lot (20,000 ft²) | 400 gal · 80 pails | $4,000–$6,000 |
| One acre (43,560 ft²) | 871 gal · 175 pails | $8,712–$13,068 |
Doing it yourself costs the sealer plus a squeegee, crack filler and cleaner. It saves the most on a sound driveway with few cracks. Large lots, badly cracked pavement and anything that needs routing or hot-pour crack sealing are better left to a contractor. The sealcoating cost guide explains what a fair bid includes and where cheap bids cut corners.
Timing
When Should You Sealcoat?
New asphalt: wait. New pavement is commonly left 6 to 12 months before its first coat so its oils can cure. Sealing too early can keep the surface soft and make the coat peel.
How often: about every 3 to 4 years for a home driveway, 2 to 3 years for a small commercial lot, and every 2 years for busy lots and drive-throughs. Reseal when the surface turns gray and stone shows, not on a fixed calendar. Sealing more than once a year only builds up layers that crack and peel.
Order of work: repair potholes and alligator cracking first, then seal open cracks, then sealcoat, then re-stripe. Sealcoat will not hold over failed pavement.
Weather: most sealer labels call for about 50°F and rising, a dry surface, and no rain for at least 24 hours. Keep cars off for 24 to 48 hours. The When to seal tab in the calculator above puts these checks together for your pavement. For a fuller answer on whether it is worth doing at all, read is sealcoating worth it.
Commercial quantities
How Much Sealer Does a Parking Lot Need?
Parking lots use sealer by the drum or tank rather than the pail, and small rounding differences become real money. The table shows two coats at an example rate of 100 ft² per gallon per coat, before any allowance.
| Area | Gallons | 5-gallon pails | 55-gallon drums |
|---|---|---|---|
| 5,000 ft² (small lot) | 100 gal | 20 | 1.8 |
| 10,000 ft² | 200 gal | 40 | 3.6 |
| 25,000 ft² | 500 gal | 100 | 9.1 |
| One acre (43,560 ft²) | 871 gal | 175 | 15.8 |
To measure a lot you can’t walk with a tape, the parking lot calculator converts acres and square feet. Cracks should be filled before sealing; the crack seal calculator estimates that material, and the striping cost calculator prices the lines that go back down afterward.
A common mistake
Concentrate vs. Mixed Coverage Rates
Some commercial sealers are sold as concentrate and mixed with water, sand or additives before they go on. A coverage rate can be stated per gallon of concentrate or per gallon of mixed material, and the two give very different purchase quantities.
Check which one the product sheet means, and enter the rate that matches what you are buying. If you are buying concentrate, use the concentrate rate; the mixing water and sand are not part of the purchase. The sealcoat coverage rate guide explains how to read label rates in more detail, and how much driveway sealer do I need walks a home driveway through step by step.
Transparent assumptions
How this calculator works
Normalize the label: coverage per pail is divided by the pail's actual gallons. Many pails sold as 5-gallon hold 4.75.
Calculate each coat: area × coats ÷ coverage per gallon per coat. No hidden roughness factor is added; use the low end of the label range on porous pavement.
Round the purchase: an allowance you can see is added, then gallons round up to whole containers, and the leftover is shown.
Compare DIY and pro: pails × your price gives the material cost. The pro range is area × the national rate for your coat count, never below the $150–$400 minimum. Crack filling adds $0.50–$3.00 per foot.
Check the timing: new asphalt waits 6 to 12 months. Reseal every 3 to 4 years for a driveway, 2 to 3 for a small lot and about 2 for busy lots, sooner if the surface grays. Failed pavement and open cracks come first.
Formula used
- Gallons = Area (ft²) × Number of coats ÷ Coverage (ft² per gal per coat)
- Containers = Gallons × (1 + Allowance %) ÷ Container gallons, rounded up
- Area covered = Available gallons × Coverage ÷ Number of coats
- Pro cost = Area × $0.20–$0.30 per ft² (two coats), at least $150–$400
Quick reference
Sealer needed and sealcoating cost by size
| Surface | Area | Sealer (2 coats) | 5-gal pails | Pro cost (2 coats) |
|---|---|---|---|---|
| 1-car driveway (10 × 20 ft) | 200 ft² | 4 gal | 1 | $150 – $400 |
| 2-car driveway (20 × 20 ft) | 400 ft² | 8 gal | 2 | $150 – $400 |
| 3-car driveway (30 × 20 ft) | 600 ft² | 12 gal | 3 | $150 – $400 |
| Long driveway (12 × 80 ft) | 960 ft² | 19.2 gal | 4 | $192 – $400 |
| Small parking lot | 5,000 ft² | 100 gal | 20 | $1,000 – $1,500 |
| Medium parking lot | 20,000 ft² | 400 gal | 80 | $4,000 – $6,000 |
Common questions
Frequently asked questions
How much does it cost to sealcoat a driveway?
A contractor charges about $0.15 to $0.25 per ft² for one coat and $0.20 to $0.30 for two, but small jobs carry a minimum of about $150 to $400. Most home driveways cost the minimum. Crack filling is usually extra.
How many gallons of sealer do I need per square foot?
Divide one gallon by the label's coverage per coat. At 100 ft² per gallon, one coat uses 0.01 gallon per square foot and two coats use 0.02. Rough or porous pavement takes more, so use the label rate for your product.
How many 5-gallon buckets of driveway sealer do I need?
At 100 ft² per gallon per coat, a 5-gallon pail covers about 500 ft² for one coat. A 400 ft² two-car driveway needs 2 pails for two coats, and a 1,000 ft² driveway needs 4. Check the actual fill; many pails hold 4.75 gallons.
Is it cheaper to seal your own driveway?
Usually, if the driveway is sound and has few cracks: you pay for sealer, a squeegee and crack filler instead of a contractor's minimum charge. A contractor makes more sense for large or badly cracked pavement, or when you want hot-pour crack sealing and commercial-grade sealer.
How long should new asphalt cure before sealcoating?
Commonly 6 to 12 months. New asphalt needs time for its oils to cure; sealing too early can keep it soft and cause the coat to peel. The When to seal tab works out how many months are left.
How often should a driveway be sealcoated?
About every 3 to 4 years for a home driveway, 2 to 3 years for a small commercial lot and every 2 years for busy lots. Reseal when the surface looks gray and worn rather than on a rigid schedule; sealing more than once a year only builds up layers that peel.
What temperature do you need to sealcoat?
Most sealer labels call for about 50°F and rising, a dry surface, and no rain for at least 24 hours. Keep traffic off for 24 to 48 hours. The product label's limits control.
How many coats of sealcoat should I apply?
Two thin coats are common on driveways and worn lots, but the product's instructions decide the coat count, application rate and time between coats.
Should I crack seal before sealcoating?
Yes. Sealcoat is a thin coating and will not bridge cracks. Fill or seal the cracks first, let them set, then sealcoat. The crack seal calculator estimates that material.
When the plan is ready
Need a contractor for the work?
Use the estimate to ask better questions, then find the companies in your market who do this kind of work.
- Sealcoating Contractors
- Crack Sealing Contractors
- Asphalt Paving Contractors
- Asphalt Maintenance Contractors
For property owners
Looking for a pavement contractor?
Use The Pavement Directory to search asphalt, concrete, sealcoating, striping, ADA access, and pavement maintenance contractors by service and location. Always verify license, insurance, references, and written scope before hiring.
Search contractorsFor contractors
Are you a pavement contractor?
Contractors can add or claim a company profile to help property owners find pavement professionals by service, location, and specialty.
Before you hire: Costs vary by region, project size, access, materials, labor, traffic control, disposal, site conditions, and scope. Use written proposals and contractor-specific pricing before making decisions.
